outer squeegee install?
outer squeegee install?
hey guys ,i got my seal kit from datsport last week and noticed that the outer squeegee pcs have aluminum inside the rubber ,now on my 68 4dr the oem squeegee is stapled on .just wounder'n if there is a good way to mount the new squeegees with out F'N things up?
ding ding dong dong all night long long.
-
- Posts: 16
- Joined: 12 Aug 2009 11:20
Re: outer squeegee install?
i talked to the datsunland socal dude at the heritage museum recently. the only parts of the install i can remember were "pull up chrome trim" and "its a 4 beer job".
Re: outer squeegee install?
talking to him is a 2 beer job!ohpyramids wrote:i talked to the datsunland socal dude ... "its a 4 beer job".
IIRC you remove the old staples and replace w/the new section.
byron wrote:I'd be all over that like a fat kid on a smartie.
okayfine wrote:Sense doesn't always have everything to do with it, and I speak from experience.
-
- Supporter
- Posts: 322
- Joined: 27 Jul 2006 14:15
- Location: Salem, Oregon
Re: outer squeegee install?
I installed my sqeegees with tiny rivots (3/32). I used the old staple holes to line it up. I have since found a set of sqeegees that you do not need to install anything. Just plug them in! They have a small S/S edge on them that goes along the S/S window strip. Looks good when installed. No one notices the stainless piece.
Re: outer squeegee install?
ya ill have to look at them again and figure the best way for me to make it work,
ding ding dong dong all night long long.
Re: outer squeegee install?
Did you ever get this figured out. I didn't see this thread until now. I have the Datsunrestore kit and it was super easy. I removed the window glass. Use a pry bar on the inside of the trim and it takes almost no effort or force to get them off. I then used a grinder to remove the staples. No need to be careful because the outer metal strip gets thrown away. My set came with about 12 clips to hold the squeegee in place. Just double check that everything is aligned properly before putting the clips on because they look like a bitch to remove after they are installed. Then just press the trim piece back into place.
"An intercooler...has never been, nor should ever be, considered icing on the cake. A proper intercooler is more cake."
Corky Bell, Maximum Boost
"one of the little things that add up"
-defdes
Corky Bell, Maximum Boost
"one of the little things that add up"
-defdes
Re: outer squeegee install?
i have my squeegees all done ,i never got any clips with mine so i got my dremel and ground off the old staples,then i drilled out the staple holes and squeegees then got my staple gun and just re stapled them on, it worked just fine for me.
ding ding dong dong all night long long.
-
- Supporter
- Posts: 322
- Joined: 27 Jul 2006 14:15
- Location: Salem, Oregon
Re: outer squeegee install?
Good job. I am curious how you "stapled" the steel backing with the rubber tab. I know the holes are there but how did you line up the staples? Did you use a commercial staple gun or ????
I used small rivots and drilled out the staple holes. I never fiegured out how to staple these parts. Help me out!
I used small rivots and drilled out the staple holes. I never fiegured out how to staple these parts. Help me out!
Re: outer squeegee install?
i used the metal strip for a template ,marked the old staple holes on my squeegee witch has steel in side the rubber base ,then drilled the holes out a tad bigger,i have a stapler that fits in and the staples were the right size.looks good to me.
ding ding dong dong all night long long.
-
- Supporter
- Posts: 322
- Joined: 27 Jul 2006 14:15
- Location: Salem, Oregon
Re: outer squeegee install?
You are a craftsman! Well done! Yankee ingenuity at it's best.
Re: outer squeegee install?
welll i think it would be canuck ingenuity at its best eh.
ding ding dong dong all night long long.
-
- Supporter
- Posts: 322
- Joined: 27 Jul 2006 14:15
- Location: Salem, Oregon
Re: outer squeegee install?
You win ONE hockey game and ...!
-
- Supporter
- Posts: 322
- Joined: 27 Jul 2006 14:15
- Location: Salem, Oregon
Re: outer squeegee install?
Enjoy the ride. Well done on the install.