L20B engine parts for sale

[SteveEdmonton]

Sad times-- my 510 is gone and it's time to clean out the rafters. These are the engine-related parts remaining.

I have pictures of all parts but for most of this stuff you already know what it is. However, I will gladly send photos if you give me your email address. (It's too time consuming to add pics here-- plus, it clogs up the site something fierce.)

NOTE: the number after the part is the price in dollars (USD or CAD) for each of the parts (for example, below: I have 2 matchbox EI dizzy modules for sale for $45 each).

Shipping by Canada Post is usually the cheapest option, and would be added. PayPal or Interac e-transfer work great.

1 single-groove crank pulley, washer, bolt, clean & painted 15 SOLD
1 Nissan OHC rocker cover with cap 40
1 NIB Nissan chrome rocker-cover cap (early style) 10 SOLD
1 U20 cam (from L20B) 20 SOLD
2 stock 4-blade plastic fan, excellent condition 15 each BOTH SOLD
1 NIB AC-Delco starter 35 SOLD
1 NIB Beck-Arnley water pump 25 (fan-clutch type)
2 used fuel pumps (Nikki, Kyosan Denki) 10 each
1 used Hitachi alternator, very good working cond 20 SOLD
1 matchbox EI dizzy D4K8-07 60 SOLD
2 matchbox EI dizzy modules 45 each SOLD
1 EI dizzy D4F6-04, no module 20 SOLD
1 single-point dizzy, rebuilt, D4A2-01 25
1 single-point dizzy, D411-88 20
1 dizzy vacuum advance metal tube 5
1 NIB Repco cap & rotor 20
1 NIB Nissan ignition resistor 10 SOLD
1 stock intake manifold 5 SOLD
1 stock air cleaner complete incl heat-riser tube, excellent condition 20
1 Felpro copper head gasket (L16, L18, L20B) 25
1 NIB Napa stock fuel filter 5
1 NIB Timken front-cover oil seal 5
1 NIB Nissan inner oil-pump gasket 3 SOLD
1 NIB Intermotor PCV valve 5
misc. carb-linkage pushrods & linkage rods

[SteveEdmonton]

Additional item:
Stock fan shroud, good condition, incl. bolts 15 SOLD

[CP]

Do you have a head? U67?

[SteveEdmonton]

A few more items to add-- I think this is "it" now, finally. Pics available by email on request.

1 set ARP head-studs (10 studs), 150 & 172 mm long, incl all washers & nuts, never used 40 SOLD
20 rocker arms (1 set of 8, 1 group of 8, 1 group of 4), all seem to be in good condition 4 each (BOTH sets of 8 SOLD)
22 lash pads-- sell as a group 10 SOLD
oil fill cap, black plastic, excellent condition 5
3 metal engine hoisting hooks, 3 metal water inlet elbows (at rear of head, for heater), 3 timing-chain covers (that bolt onto front of head) 2 each
metal thermostat bypass tubes, metal (1 solid, 1 with rubber-hose section in middle) 5 each
rubber oil-breather hose (tapered, one end bigger than the other) 5
1 set of NIB valve seals (unsure of brand) 5

[SteveEdmonton]

Set of special 510-specific tools-- $20 apiece or all 4 of these for $60.

Oil-pump priming rod (for use with electric drill, but I suppose you could try twiddling it by hand if you really want to) SOLD
Tranny input shaft (to use as clutch aligning tool)
Driveshaft yoke (stuff this into the rear of your tranny to keep the oil inside)
Cam-chain support wedge (to prevent the cam-tensioner from going sproing when you're removing the head-- thereby saving you from having to remove the crank pulley and front cover)

IMG_2467 comp.jpg (139.65 KiB) Viewed 881 times