The 510 Realm

A bolt on rear sway bar for a 510. Bar itself is nickel plated. Has all brackets to mount.

$200.00

Prefer pick up only in Sacramento California area

Mike

I have a set of 510 axles for sale. Are in excellent condition with maybe 50 miles on new U joints. $200 plus shipping from Sacramento, Ca.

Mike

A set of FIVE wheels and tires to fit Datsun 510 or similar. 13" x 6" with 4" backspace, 114.3 mm spacing, drilled for 18mm shouldered lug nuts. Wheels are mounted with Toyo 205 x 60 x 13 RA1's. Lug nuts are 12mm x 1.5 thread and are included. Pick up only in Sacramento, California. W...

HOW TO HOTROD AND RACE YOUR DATSUN by Bob Warr. HOW TO MODIFY YOUR NISSAN AND DATSUN OHC ENGINE by Frank Honsowetz HOW TO REBUILD YOUR NISSAN AND DATSUN OHC ENGINE by Frank Honsowetz CLYMER DATSUN SERVICE AND REPAIR HANDBOOK, 1968-1972 HAYNES DATSUN 510 OWNERS WORKSHOP MANUAL HOW TO KEEP YOUR DATSUN...

Hello group...…...well the 510 race car is back from paint and now starting to bolt on parts. Is there a source for tail light gaskets?? Also looking for tow hooks that would bolt to the original bumper bracket mounting holes in the rear.

Thanks

Mike Summers

Yup that is the problem....most everyone says, just use a breaker bar and a 1/2 drive. Well the previous owner used that technique. I don't think I have ever had a drain plug in so tight...and the 1/2 drive is starting to round inside the plug. What is needed is a 14mm SQUARE drain plug too. It is s...

I have a 280 zx trans that I am bolting to my L18 motor. What size is drain plug on the 280zx trans?? Looks to be square but what size is it?? Trying to get staff in a generic auto parts store to find one has been maddening. Thanks all

Mike

Sacramento, Ca

Selling my just rebuilt Datsun L16 motor. This lower end of motor was checked by a EXPERT Datsun motor builder and found to be in good condition. He totally rebuilt the head: surfaced, rocker ratios corrected, new valves and valve job, mild comp cam installed and degreed. New water pump. Comes with ...

Great Steve, thanks...….if you have one I will send my email address

Mike

Need a automatic flexplate, 5 bolt for a L16/18 motor. This is a race car project
HELP PLEASE !!!
Mike Summers
California

Yup you are right there........these are aftermarket and I have spent a hour just moving them around to different angles and bolt combos.........they just are not going to work as is. Is there a link to the discussion or just type in motor mounts in the search box.

Another question........is the pic of this motor mount in the correct position?? Or do I have it upside down??

Mike

Hi group......... So my car has been apart for some time.........there are two distinctly different motor mounts. One is a one piece stamped unit. The other has a couple pieces factory welded together........are they the same height?? Which side does the multi piece go on?? Passenger, driver??? Help...

Hey Group,
Is there a source for the four shouldered bolts and nuts, per side, that connect the drive shafts to the wheel hubs? I am in need of a full set of 8 if anyone out that has them for sale. Not something that I will find in my hardware store metric section.

Thanks

Mike Summers

Hello group...... I have assembled these struts to go on my vintage 510 race car. Tubes cut down, Koni inserts, adjustable spring perches, new disks. Problem is, I cant remember (old racer guy) exactly which model there were. I know they are 280's but not sure what year and model. Why?? I need to or...